|
在用VB制作软件封面和界面时经常要用到三维字体，一般的方法是先用专门的软件（如Xara3d等）制作出三维字体的图片，然后再用图片框等控件显示出来。这样虽然简单，但其缺点有二：一是要额外增加控件和图片，这样势必会增加程序的大小；二是在VB中图片的加载速度不敢恭维。如能用VB直接编程制作出三维字体，岂不美哉！以下是本人的一点“小技”，请笑纳！
先在VB中新建一个“工程”，然后在窗体上放置四个Command。以下是源程序：
先声明如下“通用变量”:
Dim posx, posy As Integer ''''文字的显示位置
Dim txtwidth As Integer ''''文字轮廓宽度
Dim str As String ''''欲显示的文字
Private Sub Command1_Click() ''''显示凸起三维文字
Dim i As Integer
str = "显示凸起三维文字"
Me.Cls
Me.ForeColor = RGB(255, 255, 255)
For i = 1 To txtwidth
Me.CurrentX = posx - i
Me.CurrentY = posy - i
Me.Print str
Next i
Me.ForeColor = RGB(0, 0, 0)
For i = 1 To txtwidth
Me.CurrentX = posx + i
Me.CurrentY = posy + i
Me.Print str
Next i
Me.ForeColor = RGB(0, 0, 255)
Me.CurrentX = posx
Me.CurrentY = posy
Me.Print str
End Sub
Private Sub Command2_Click() ''''显示凹陷三维文字
Dim i As Integer
str = "显示凹陷三维文字"
Me.Cls
Me.ForeColor = RGB(0, 0, 0)
For i = 1 To txtwidth
Me.CurrentX = posx - i
Me.CurrentY = posy - i
Me.Print str
Next i
Me.ForeColor = RGB(255, 255, 255)
For i = 1 To txtwidth
Me.CurrentX = posx + i
Me.CurrentY = posy + i
Me.Print str
Next i
Me.ForeColor = RGB(0, 0, 255)
Me.CurrentX = posx
Me.CurrentY = posy
Me.Print str
End Sub
Private Sub Command3_Click() ''''显示阴影三维文字
str = "显示阴影三维文字"
Me.Cls
Me.ForeColor = RGB(100, 100, 100)
Me.CurrentX = posx + txtwidth
Me.CurrentY = posy + txtwidth
Me.Print str
Me.ForeColor = RGB(0, 0, 255)
Me.CurrentX = posx
Me.CurrentY = posy
Me.Print str
End Sub
Private Sub Command4_Click() ''''显示倾斜三维文字
Dim i As Integer
str = "显示倾斜三维文字"
Me.Cls
Me.ForeColor = RGB(100, 100, 100)
For i = 1 To txtwidth
Me.CurrentX = x + i
Me.CurrentY = y + i
Me.Print str
Next i
Me.ForeColor = RGB(0, 0, 255)
Me.CurrentX = posx
Me.CurrentY = posy
Me.Print str
End Sub
Private Sub Form_Load()
posx = 100
posy = 100
txtwidth = 50
Me.FontSize = 30
End Sub
以上程序在win98/vb6.0/233下调试通过。
没有相关教程
| 
注：本站部分文章源于互联网，版权归原作者所有！如有侵权，请原作者与本站联系，本站将立即删除！ 本站文章除特别注明外均可转载，但需注明出处！ [MinTao学以致用网] 
